![]() Firstly you should run the QNAP QFinder application which will scan your network for NASs and should find your NAS The QNAP TS-412 initially requires you to set up how you want the NAS to use the drives that it contains in the case of the TS-412 we have four drives and can configure the unit to operate in what is known as RAID5 which allows the NAS to resist the failure of a single hard drive without losing any data. ![]() We will now concentrate on setup for use specifically with any of our Naim Music Servers (UnitiServe, HDX or NS0x) under Windows here, however, setup under OSX will be the same as the QNAP NAS uses a web-based setup interface and these instructions should be applicable for all operating systems with any differences being restricted to any specific display characteristics of the browser that you choose to use. We shall assume that you have installed the drives in the unit, have installed the QNAP QFinder software on your computer either from the manufacturers CD (if applicable) or by downloading it from the manufacturers website in accordance with the manufacturers instructions. Naim Audio cannot be held responsible for any discrepancies between these instructions - which are provided as-is - and your specific NAS. Other versions of firmware (or other models of QNAP NAS) may be slightly different to these instructions however should be broadly similar. NOTE : These instructions were created using a QNAP TS-412 NAS running firmware that was current at the time of writing. Naim Audio recommends the use of its own Naim Music Servers for best functionality and quality when used in conjunction with a Naim Audio UPnP Client playback device. ![]() NOTE : The UPnP server that forms part of the software on this NAS is not endorsed by Naim Audio and should only be used with our UPnP clients once the customer has ascertained that the software provides at least the minimum functionality and stability that the customer requires - Naim Audio cannot be held responsible for the functionality of, or any bugs in, the UPnP server software on this NAS. Not sure what this is supposed to do or it's function.1 QNAP TS-412 Setup NOTE : These instructions show how to set up the appropriate folders for use with a Naim Music Server only and are not configuration instructions to enable a Naim UPnP client to use the NAS as a music source directly. I entered the use and password and I now have just and empty Command Prompt like window open with nothing but. Now a window opens "Mount NAS" the IP is selected protocal is SMB/CIFS. previously when I clicked Newwork drives it opened a explorer shoulding the contents of the NAS. ButApart from a few apps and security settings I hadn't really changed any of the settings. I therefore had to re setup all the folders etc.Īnd all this started! It was all fine before the factory reset. When I switched it back on it reset to factory setting. First I decided to switch off the NAS and clean the dust. I therefore decided to try and find out why. I was very happy with it.Ī couple of months ago I stopped being able to connect from my iPhone/iPad via the internet using Qfile but it still worked via Wifi. Yes the NAS was working fine and has been working for years. Is there many be something set up wrong on the NAS? The device or resource (IP Address) is not set up to accept connections on port "The File and printer sharing (SMB)". The remote device or resource won't accept the connection Detected When entering the IP address in explorer I get the error.Ĭheck the spelling of the name.Ect. But if I click on the icon I am taken to the splash screen of the NAS. I can see the NAS in Media Devices in Windows Explorer. I have checked and updated my Windows Credentials. I still can not see the NAS in my network in Explorer. I have installed WinSCP and I can connect to the NAS. PS C:\WINDOWS\system32> Get-SmbServerConfiguration | Select EnableSMB2ProtocolįYI. PS C:\WINDOWS\system32> Get-SmbServerConfiguration | Select EnableSMB1Protocol What Commands, where and why when SHH is not working? Sorry but I do not understand what you are asking. So did you enter the given commands when SSH access is not working ? Well before you said SMB1 is enabled, so without correct feedback, any help is tedious work
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |